Escursionismo e Torce

Elegant, tactical and indestructible titanium pen, useful also as crystal crystals and for self defense with "sliding shutter" grafting system.

* Weight: 30g
* Total length: 133mm.
* Material: titanium
* Diameter: 9.3 mm.
* Glass breaking tip: tungsten steel
* Ink: black with Fisher PR4 refill. Writes at temperatures from -35 ° to over 120 °, under water, on dirty and oily surfaces, lasts 15 times longer than a normal non-pressurized refill, can draw a continuous line of 14 km thanks to the special thixotropic ink, from semi-solid consistency, which is made fluid by the special tungsten sphere.

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 1x Cree XP-G2 S3 with a life cycle of 50,000 hours and with a lighting diameter of 100 °
Operating Modes: 4 light powers, selectable with the dedicated dedicated button
Powers and Durations: 380 Lumens (0.15h.) -> 145 Lumens (1h.) -> 38 Lumens (4h.) -> 1 Lumen (60h.)
Peak of power: 1020 candles
Maximum illumination distance: 64m.
Ignition method: Power on and off button
Light selection method: Light selection button
Body: aeronautical aluminum with anodizing degree HA III
Battery: Integrated 280mAh Li-Ion type, equipped with integrated MicroUSB charging system
Measurements: 4.33cm (Lenght) - 2.54cm (Width) - 1.15cm (Thick)
Weight: 13.4g. - battery included
Accessories: steel ring for attachment to the key ring
Waterproof: as per IP54 standard, it resists dust and light splashes of water
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with integrated charging system via MicroUSB port (cable not included in the package); when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The rear hook of the torch, designed to anchor it to a key ring or other equipment, withstands a traction of up to 30kg.

IMPORTANTE: questa batteria non è una comune batteria formata da 2xCR12A da 3V e non può essere utilizzata in apparecchi che utilizzano batterie CR123A poichè ha un diametro differente. Richiede inoltre un apposito caricabatterie per essere ricaricata e non possono essere utilizzati normali caricabatterie per batterie di tipo Ni-Mh o Li-Ion. Non ci riteniamo responsabili in caso di utilizzo errato delle batterie, di uso a polarità invertite, di errori in fase di ricarica o di eventuali danni su apparecchiature non idonee al funzionamento con queste batterie.

CARATTERISTICHE BATTERIA

* Batteria ricaricabile Li-Ion 18650 cilindrica
* Voltaggio nominale: 3.6V
* Capacità: 2900mAh - 8A
* Polo Positivo: Sporgente
* Circuito di protezione PCB per la protezione interna del voltaggio
* La protezione PCB previene i sottovoltaggi a 2.5V e i sovravoltaggi a 4.25V
PRECAUZIONI BATTERIA

* Non lasciare incustodite le batterie durante la fase di carica * Non ricaricare sopra tappeti, tavoli in legno o materiali infiammabili
* Non siamo responsabili per danni derivati dalla manomissione delle batterie
* Non siamo responsabili per un uso incorretto o con polarità invertite delle batterie

SPECIFICHE TECNICHE BATTERIA:

* Capacità: 2900mAh nominali
* Dimensioni: 18.5+/-0.2 mm diametro x 69+/- 0.2mm altezza
* Peso approssimativo: 49.9g
* Voltaggio nominale medio: 3.6V
* Voltaggio di picco: 4.2V
* Potenza: 8A
* Cicli vitali: > oltre i 500 cicli

IDEALE PER I SEGUENTI MODELLI NITECORE O PER QUALSIASI UTILIZZO CON TEMPERATURE ESTERNE SOTTO LO ZERO:
CONCEPT 1 - EC23 - HC33 - MH12GTS - MH23 - MH25GTS

Cordura tactical backpack, light and durable, designed for hiking, tactical and urban use.

Features and Materials:

- 1000-denier Nylon Cordura resistant to water and abrasion with parts in synthetic velvet
- External treatment for fabrics that ensures resistance to dirt and facilitates maintenance
- Designed for intensive use and hiking, even for several days
- Single 25L front compartment and completely openable and sealed by zip
- Japanese production YKK zip
- Frontal and internal compartments to accommodate documents and small tools
- Padded and ventilated back and shoulder straps
- Reinforced handle and stitching
- Reinforced and long zip pulls, comfortable to use even with gloves
- Large velcro area to anchor patches and various objects
- Compression straps for anchoring objects and compacting the load
- MOLLE compatible front and side parts to expand and modulate the backpack
- Side nylon straps for attaching objects and additional buffets
- Possibility to accommodate water bottles or hydratation pack, with an external hole dedicated to the straw
- Modulable through various expansion compartments that can be purchased separately
- Dimensions: 45x28x16.5 cm.
- Volume: 25 l.
- Weight: 1.46 kg.

NOTE: The helmet shown in the pictures is for display purposes only and is not included with the product

Led: 1x Cree XP-G3 S3 with a life cycle of 50,000 hours and with a lighting diameter of 100 ° - 2x CRI> 90 with white light (19 Lumens x 25h.) - 2x auxiliary LEDs with red light (9 Lumens x 38h .)
Operating Modes: 4 light powers, selectable with the dedicated dedicated button and 2 signaling modes
Powers and Durations: 550 Lumens (1h.) -> 190 Lumens (17h.) -> 33 Lumens (50h.) -> 1 Lumen (330h.) -> S.O.S. -> Beacon Light
Power peak: 3900 candles
Maximum illumination distance: 125m.
Ignition and selection method luminsa: Two power-on, power-off and selection buttons; one for white light and one for red light
Body: ABS
Batteries: 3.7V and 1800mAh integrated Li-Ion, not removable, equipped with integrated MicroUSB charging system
Measurements: 6.3cm (Length) - 4.3cm (Width) - 3.1cm (Thickness with front support)
Weight: 99.5g. - battery included
Accessories: front elastic band - USB / MicroUSB charging cable
Waterproofing: as per standard IP67, submersible up to 1m depth
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with integrated charging system via MicroUSB port (cable included in the package); when charging, an integrated LED underneath the buttons will show the status and switch off automatically when the charging is completed. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The torch lens allows to illuminate at 100 ° amplitude. The tilt adjustment system allows you to lower the torch up to 60 ° - the torch can be powered via the USB cable while remaining on, so you have constant lighting when needed - the 550 Lumens Turbo mode is automatically lowered to 190 Lumens to allow the LED to cool, then return to produce 550 Lumens.

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 1x Cree XP-G2 S3 with a life cycle of 50,000 hours and with a lighting diameter of 100 °
Operating Modes: 4 light powers, selectable with the dedicated dedicated button
Powers and Durations: 380 Lumens (0.15h.) -> 145 Lumens (1h.) -> 38 Lumens (4h.) -> 1 Lumen (60h.)
Peak of power: 1020 candles
Maximum illumination distance: 64m.
Ignition method: Power on and off button
Light selection method: Light selection button
Body: aeronautical aluminum with anodizing degree HA III
Battery: Integrated 280mAh Li-Ion type, equipped with integrated MicroUSB charging system
Measurements: 4.33cm (Lenght) - 2.54cm (Width) - 1.15cm (Thick)
Weight: 13.4g. - battery included
Accessories: steel ring for attachment to the key ring
Waterproof: as per IP54 standard, it resists dust and light splashes of water
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with integrated charging system via MicroUSB port (cable not included in the package); when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The rear hook of the torch, designed to anchor it to a key ring or other equipment, withstands a traction of up to 30kg.

Multi-functional All-in-one Vehicle Gadget
The ultimate car utility, the Nitecore VCL10 combines all of the features that you need when you have a vehicular emergency. The VCL10 at its core is a 12V USB adapter, sharing that familiar shape that fits into standard cigarette lighter receptacles. While plugged in, the VCL10 can charge just about any USB powered device you have ranging from smart phones to tablets. The VCL10 is also outfitted with a fully functional glass breaker, so in emergency situations it can be used to shatter a window for a quick escape. The body of this gadget is magnetic, making it easy to store hands free which makes the lighting features even more useful. Speaking of the lighting features...

Two Emergency Lighting Modes
With an internal rechargeable li-ion battery, the Nitecore VCL10 can produce two forms of light for emergency or utility purposes. The first light is a standard white LED that is great for looking in or outside of your vehicle in the dark. The second light is an emergency red light with flashing modes that can be used to signal for help in the event of a breakdown or other disaster. Both lights are mounted on a 90 degree tilt-able head that can be adjusted to suit your needs.

Features:
Multi-functional USB QC vehicle charger
Transformer loss compensation (TLC) enabling automatic adjustment of output voltage
Multi protection for overload, short-circuit and overheating
White beam and red warning light controllable with one button
Built-in photo-detector enabling quickened flashes when detecting oncoming vehicles
90 degree tilt-able head
Stainless steel glass breaker tail design
Magnetic body
1 Meter impact resistance
Certified by RoHS, CE, FCC and CEC
Specifications:

White Beam: 25 Lumens - 3 Hours
Red Warning Light: 350mW - 20 Hours
Beam Distance: 7 Meters
Peak Beam Intensity: 12cd
Input: DC 12V 2.5A (MAX)
Output: DC 5V 2.4A (MAX)
Quick Charge 3.0: DC 3.6V-12V 2.4A (MAX)
Quick Charge 2.0: DC 5V / 9V / 12V 2.4A (MAX)
Dimensions:
Length: 3.09" (78.5mm)
Width: 0.96" (24.5mm)
Height: 0.91" (23mm)
Weight: 44.5g (1.57oz)

Key Features:
* Integrated charging system for Li-ion batteries via Micro-USB port on the shank
* Rechargeable NITECORE 18650 battery (NL1835HP, 3.7V, 8A, 3,500mAh) included in the package
* Uses a CREE XHP35 HD LED for maximum output power of 1800 lumens
* Maximum light intensity at the 12760cd center point. and maximum capacity of 226 meters
* Glass and parabolas with anti-reflection, crystal coating and PDOT (Precision Digital Optics Technology)
* Integrated potentiometer with indicator light indicating residual charge and residual voltage of the battery
* Built in solid aeronautical aluminum alloy with anodizing to military specifications
* IP68 waterproof and submersible (up to 2m depth for 30min)
* Resistant to impacts and falls up to a maximum of 1m. of height
* Possibility to be positioned vertically, by candle
 

It is recharged like a smartphone!
This torch is equipped with a charging system via a Micro-USB plug on the shank, which allows you to recharge a battery of type 18650 (included in the package) without having to remove it from the torch.

Led: 1x Cree XHP35 HD - with a life cycle of 50,000 hours
Operating Modes: 5 light modes and 3 special modes all electronically regulated
Powers and Durations: 1800 Lumens (0.5h) -> 900 Lumens (2.15h) -> 240 Lumens (5.45h) -> 70 Lumens (19h) -> 1 Lumens (250h.) -> Strobo -> Beacon -> S.O.S.
Peak of power: 12760 candles
Maximum illumination distance: 226m.
Ignition method: Rear button with "Momentary On" system for luminous signals
Light selection method: Front button located under the head
Head: aeronautical aluminum
Body: aeronautical aluminum
Finishing: anodized, Type III
Lens: ultra-clear hardened glass with anti-reflective coating
Battery: included in the package, 1x Li-ion 18650 rechargeable from 3.7V, 8A, 3500mAh - If necessary can also work with 1x 18650 Li-Ion 3.7V or 2x CR123 3.0V without being able to reach 1800 lumens of power
Measurements: 14.4cm (L) - 2.54cm (D stem) - 2.54cm (D head) - 2.60cm (D shank)
Weight: 99.5g. without the battery inserted
Accessories: wrist strap, belt cordura sheath, spare o-ring, clip, removable tactical ring, USB / Micro-USB charging cable, NL1835HP battery
Waterproofing: as per IP68 standard, submersible up to 2m. of depth for 30min.
Impact resistance: withstands falls from 1m in height
Italian Nitecore Italia Warranty: 5 year guaranteed torch - 12 month guaranteed battery

Powers and durations certified in laboratory by ANSI / NEMA FL1 standard using 1x Li-ion18650 3.7V 3500mAh - in different conditions of use or using different batteries, data may vary

Specifications:
Serrated stainless steel 420HC
screwdriver Middle
Apripacchi
bottle opener
Can Opener
Phillips screwdriver
Ruler (1 in/2.54 cm)
Scissors
screwdriver Middle
Pointy nose pliers and spring opening
Normal pliers with spring aperrtura
Cutter with spring opening
cutters
File for iron and wood

Details:
25-year warranty
Outer blade with liner lock closure
removable clip
Stainless steel body
Stainless steel handles

size:
Blade Length: 6.6cm.
Length when closed: 9.7cm.
Weight: 198.4g.

HUNTING KIT

the set includes:

- Nitecore P30 torch

- RSW1 Remote Attack

- Rechargeable battery with integrated 3.6V 2600mAh micro-usb

Led: 1x Cree XP-L HI V3 with a life cycle of 50,000 hours
Operating Modes: 5 electronically regulated + Strobo, S.O.S. and Beacon
Powers and Durations: 1000 Lumens (1h) -> 400 Lumens (3h) -> 220 Lumens (5h) -> 70 Lumens (17h) -> 1 Lumen (680h) -> Strobo -> SOS -> Beacon
Peak of power: 95500 candles
Maximum illumination distance: 618m.
Ignition method: Back button
Light selection method: Front button
Head: aeronautical aluminum
Body: aeronautical aluminum
Finishing: anodized, Type III
Lens: ultra-clear hardened glass with anti-reflective coating
Batteries: sold separately - 1x 18650 3.7V or 2x disposable / rechargeable CR123A batteries from 3.0 / 3.7V sold separately
Measurements: 14.1cm (L) - 2.54cm (D stem) - 5.0cm (D head)
Weight: 165g. - batteries not included
Accessories: clip, wrist strap, cordura belt sheath, spare o-ring, anti-roll ring
Waterproofing: as per standard IPX-8, submersible up to 2m. of depth for 30min.
Impact resistance: withstands drops from 1.5m in height

Key Features

Magnetic, portable and pocket-sized USB charger with charging and discharging functions
Compatible with Li-ion and IMR cylindrical batteries
Integrated USB 2.0 ports, both input and output
It intelligently identifies the positive and negative poles of the batteries
White LED light that can be used as an auxiliary torch, with 3 different levels of brightness
Charge and discharge indicator with 3 red LEDs to indicate the percentage reached
Automatically identify the battery voltage and select the appropriate type of charge (CC, CV)
Compatible with power banks, 5V solar panels and USB power supplies
Made of PC + ABS resistant to heat, flame and fire
 

Technical specifications

Input voltage: 5V or 500mA
Output Voltage: 4.2V ± 1% (BATTERY) / 5V ± 5% (USB) - 1A MAX
Dimensions: 245x24.5x18.5 mm.
Weight without batteries: 27.8g.
Compatible with IMR / Li-Ion batteries: 12650, 13450, 13500, 13650, 14350, 14430, 14500, 14650, 16500, 16340 (RCR123), 16650, 17350, 17500, 17650, 17670, 17700, 18350, 18490, 18500, 18650, 18700, 20700, 21700, 22500, 22650, 22700, 25500, 26500, 26650, 26700 (Compatible in general with any cylindrical Li-ion rechargeable battery and with 3.6 / 3.7V voltages)

Precautions:

Do not recharge different types of batteries in addition to those indicated
Do not leave the batteries unattended during charging operations
When the batteries are charged, remove the batteries from the charger before removing the electrical outlet to prevent the batteries from being discharged

ATTENTION: the batteries shown in the picture are not included.

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 1x Cree XP-G2 S3 with a life cycle of 50,000 hours and with a lighting diameter of 100 °
Operating Modes: 4 light powers, selectable with the dedicated dedicated button
Powers and Durations: 380 Lumens (0.15h.) -> 145 Lumens (1h.) -> 38 Lumens (4h.) -> 1 Lumen (60h.)
Peak of power: 1020 candles
Maximum illumination distance: 64m.
Ignition method: Power on and off button
Light selection method: Light selection button
Body: aeronautical aluminum with anodizing degree HA III
Battery: Integrated 280mAh Li-Ion type, equipped with integrated MicroUSB charging system
Measurements: 4.33cm (Lenght) - 2.54cm (Width) - 1.15cm (Thick)
Weight: 13.4g. - battery included
Accessories: steel ring for attachment to the key ring
Waterproof: as per IP54 standard, it resists dust and light splashes of water
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with integrated charging system via MicroUSB port (cable not included in the package); when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The rear hook of the torch, designed to anchor it to a key ring or other equipment, withstands a traction of up to 30kg.

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 1x Cree XP-G2 S3 with a life cycle of 50,000 hours and with a lighting diameter of 100 °
Operating Modes: 4 light powers, selectable with the dedicated dedicated button
Powers and Durations: 380 Lumens (0.15h.) -> 145 Lumens (1h.) -> 38 Lumens (4h.) -> 1 Lumen (60h.)
Peak of power: 1020 candles
Maximum illumination distance: 64m.
Ignition method: Power on and off button
Light selection method: Light selection button
Body: aeronautical aluminum with anodizing degree HA III
Battery: Integrated 280mAh Li-Ion type, equipped with integrated MicroUSB charging system
Measurements: 4.33cm (Lenght) - 2.54cm (Width) - 1.15cm (Thick)
Weight: 13.4g. - battery included
Accessories: steel ring for attachment to the key ring
Waterproof: as per IP54 standard, it resists dust and light splashes of water
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with integrated charging system via MicroUSB port (cable not included in the package); when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The rear hook of the torch, designed to anchor it to a key ring or other equipment, withstands a traction of up to 30kg.

The inspiration behind the KEY-BAR was the annoyance of the noise and disorganization of the many keys that creator Michael Taylor carries daily. In his workshop one weekend he decided to do something about his problem. After many hours of research, trial and error and several prototypes later, he arrived at the current version of the KEY-BAR.

Your KEY-BAR arrives in a hinged tin and includes:

(1) KEY-BAR with removable Titanium pocket clip in your choice of color
(2) 1/2 in. screws (1-4 keys)
(2) 3/4 in. screws (1-8 keys)
(2) 7/8 in. screws (1-12 keys)
(15) Washers
(2) O rings (allows you to adjust the tension to your liking)
(1) Key fob link

Dimensions

Length: 3.5 in

Weight: 1.6 oz

Screw post dimension: .164 in

# of keys the KEY-BAR can hold

Up to 12 with the provided screws

Up to 28 with longer screws, available here

Fits 90% of keys

No special tools are necessary for assembly.

All KEY-BARs are CNC milled from solid billet then hand finished to order.

Every KEY-BAR is 100% non-ferrous and all hardware is stainless steel so your KEY-BAR will not rust.

MADE IN THE USA

SAVANNAH, GA

PATENTED

The philosophy behind Key-Bar is simple and the result of a need: daily carry your keys in your pocket without the latter make noise and move anywhere creating hassles.

Then enters the scene creativity and inventica Michael Taylor who, after many hours of research and creation of prototypes in his small workshop in Savannah, USA, invented Key-Bar. A small keychain drive, configurable at will, that allows keys to be always in order, not to emit noise during transport and anchored fit comfortably within your pocket or attached to your belt.

The development of Key-Bar is just beginning, but its potential is enormous. And 'you can separately purchase additional accessories to be included along with keys that allow the creation of a small multi-tool ready for any eventuality daily!

Handle Material: Anodized aluminum
Handle length: 89mm.
Weight without keys: 40g.

The sales package includes:
2x Screws 1/2 ": to insert 1 to 4 keys
2x 3/4 "Screws: to insert 1 to 8 keys
2x Screws 1/12 ": to insert keys from 1 to 12
15x spacers
2x O-ring
1x correggiolo
1x titanium clip

No special tools are required to assemble and configure your Key-Bar; all handles are made from solid billets of material and CNC machined and then finished by hand.

Each Key-Bar is made with non-ferrous materials, while the screws are stainless steel, so as to ensure the maximum dell'igene and extreme ease of cleaning and maintenance.

Patented and manufactured entirely in Savannah, USA

Cutlery Collini Busto Arsizio is official dealer for Italy brand Key-Bar

1800 Power Lumens with One Battery IMR18650 - Highest Pocket Size, Only 11cm Long. And with magnetic back cap.

Laboratory Potentials and Durability Standards from ANSI / NEMA FL1 Standard using 1x 18650 IMR 3.6V 3100mAh - under different conditions of use or using different batteries, the data may vary

Led: 1x CREE XP35 HD E2 LED with a life cycle of 50,000 hours
Operating Modes: 5 electrically regulated light powers
Powers and Dates: 1800 Lumens (30min.) -> 810 Lumens (1.30h.) -> 300 Lumens (4h.) -> 80 Lumens (15h.) -> 1 Lumen (300h.) -> Strobo -> Location Beacon
Power peak: 12100 candles
Maximum illumination distance: 220m.
Power method: Multifunctional front button
Light Selection Method: Multifunctional front button
Head: Aeronautical aluminum
Body: Aeronautical aluminum
Finish: anodised, Type III
Lens: ultra-hardened hardened glass with anti-reflection treatment
Battery pack (included in the package): 1x 3.6V and 3100mAh rechargeable IMR 18650 - It can also work with 1x 18650 Li-Ion 3.7V or 2x CR123 3.0V without ever achieving 1800 lumens of power
Measurements: 11.1cm (L) - 2.38cm (D stem) - 2.45cm (D head)
Weight: 62g. - Batteries not included
Impact Resistance: Resists to 1.5m high falls
Waterproof: as standard IPX-8, immersible up to 2mt. Of depth for 30min.
Notes: Magnetic back cap can be hooked to any metal surface - to produce 1800 lumens of power, it is mandatory to have a 3.6 / 3.7V IMR18650 battery with a current output greater than 8A, such as that already supplied with the torch.

Accessory original Key-Bar made entirely of titanium; It has functions of small flat screwdriver and bottle opener. For use within their own Key-Bar

The philosophy behind Key-Bar is simple and the result of a need: daily carry your keys in your pocket without the latter make noise and move anywhere creating hassles.

Then enters the scene creativity and inventica Michael Taylor who, after many hours of research and creation of prototypes in his small workshop in Savannah, USA, invented Key-Bar. A small keychain drive, configurable at will, that allows keys to be always in order, not to emit noise during transport and anchored fit comfortably within your pocket or attached to your belt.

The development of Key-Bar is just beginning, but its potential is enormous. And 'you can separately purchase additional accessories to be included along with keys that allow the creation of a small multi-tool ready for any eventuality daily!

No special tools are required to assemble and configure your Key-Bar; all handles are made from solid billets of material and CNC machined and then finished by hand.

Each Key-Bar is made with non-ferrous materials, while the screws are stainless steel, so as to ensure the maximum dell'igene and extreme ease of cleaning and maintenance.

Patented and manufactured entirely in Savannah, USA

Cutlery Collini Busto Arsizio is official dealer for Italy brand Key-Bar

Accessory original Key-Bar made entirely of titanium; It has functions of small flat screwdriver and bottle opener. For use within their own Key-Bar

The philosophy behind Key-Bar is simple and the result of a need: daily carry your keys in your pocket without the latter make noise and move anywhere creating hassles.

Then enters the scene creativity and inventica Michael Taylor who, after many hours of research and creation of prototypes in his small workshop in Savannah, USA, invented Key-Bar. A small keychain drive, configurable at will, that allows keys to be always in order, not to emit noise during transport and anchored fit comfortably within your pocket or attached to your belt.

The development of Key-Bar is just beginning, but its potential is enormous. And 'you can separately purchase additional accessories to be included along with keys that allow the creation of a small multi-tool ready for any eventuality daily!

No special tools are required to assemble and configure your Key-Bar; all handles are made from solid billets of material and CNC machined and then finished by hand.

Each Key-Bar is made with non-ferrous materials, while the screws are stainless steel, so as to ensure the maximum dell'igene and extreme ease of cleaning and maintenance.

Patented and manufactured entirely in Savannah, USA

Cutlery Collini Busto Arsizio is official dealer for Italy brand Key-Bar

Accessory original Key-Bar made entirely of titanium; It has functions of small flat screwdriver and bottle opener. For use within their own Key-Bar

The philosophy behind Key-Bar is simple and the result of a need: daily carry your keys in your pocket without the latter make noise and move anywhere creating hassles.

Then enters the scene creativity and inventica Michael Taylor who, after many hours of research and creation of prototypes in his small workshop in Savannah, USA, invented Key-Bar. A small keychain drive, configurable at will, that allows keys to be always in order, not to emit noise during transport and anchored fit comfortably within your pocket or attached to your belt.

The development of Key-Bar is just beginning, but its potential is enormous. And 'you can separately purchase additional accessories to be included along with keys that allow the creation of a small multi-tool ready for any eventuality daily!

No special tools are required to assemble and configure your Key-Bar; all handles are made from solid billets of material and CNC machined and then finished by hand.

Each Key-Bar is made with non-ferrous materials, while the screws are stainless steel, so as to ensure the maximum dell'igene and extreme ease of cleaning and maintenance.

Patented and manufactured entirely in Savannah, USA

Cutlery Collini Busto Arsizio is official dealer for Italy brand Key-Bar

The most popular of the Leatherman pliers is now available with a new version further improved thanks to the addition of interchangeable and resistant cutters.

Tools: Stainless Steel
Handle: Stainless Steel
Closed length: 100 mm.
Open length: 160 mm.
Weight: 238 g.
Sheath: shaped, in Leather or Cordura (according to availability), with vertical or horizontal fixing

Endowment:
Plier with thin points
Interchangeable wire cutters
Flat-blade knife
Serrated knife
File for iron
File for wood
Diamond file
Saw
Screwdriver connection
Precision screwdriver insert
Large flat screwdriver
Precision flat screwdriver
Phillips screwdriver
Precision Phillips screwdriver
19cm ruler.
Bottle opener / can opener
Cable strippers
Hole for transport

Professional torch specifically designed for the identification and examination of large rough precious stones, amber or jade in gemology and jewelery. Equipped with infinite light variations from 1 to 800 lumens and concentrated light beam.

Powers and durations certified in laboratory by ANSI / NEMA FL1 standard using 1x 3500mAh 18650 3.7V Li-ion - in different conditions of use or using different batteries, data may vary.

LED: 1x Cree XP-L HI V3 - with a life cycle of 50,000 hours
Operating Modes: continuous brightness variation, from 1 to 800 Lumens
Powers and Durations: 800 Lumens (1h.) / 1 Lumen (500h.)
Power peak: 8650 candles
Maximum illumination distance: 186m.
Ignition method: Turn the torch shank clockwise
Light selection method: Turn the front circular selector clockwise and anticlockwise
Head: aeronautical aluminum
Body: aeronautical aluminum
Finishing: anodized, Type III
Lens: ultra-clear hardened glass with anti-reflective coating
Batteries: (not included - sold separately) 1x Li-ion 18650 3.7V rechargeable or 2x CR123 3.0 / 3.7V disposable or rechargeable
Measurements: 13.5cm (L) - 2.15cm (D stem) - 1.6cm (D head)
Weight: 66.5g. batteries excluded
Accessories: sheath, wrist strap, spare o-ring
Waterproofing: as per standard IPX-8 - submersible up to 2m. of depth for 30min.
Impact resistance: withstands falls from 1m in height

It has a magnetic bottom to attach it everywhere and works like a lipstick / lip gloss: turn the lower part and the "salt" diffuser cone expanding the light beam. Ideal to keep in the car for emergencies or to use during excursions or overnight stays in tents.

LED: 1x Cree XP-L HD V6 with a life cycle of 50,000 hours
Output: 1000 lumens (1h.) -> 230 lumens (6h.) -> 60 lumens (24h.) -> 1 lumen (900h.) -> beacon
Lighting distance: 166m.
Power peak: 6900cd
Battery: sold separately - 1x 18650 3.6 / 3.7V or 2x CR123 3.0 / 3.7C Li-ion battery
Measurements: 10.6cm (L) x 2.69cm (D)
Weight: 78.5g. - batteries not included
Head: T6061 aeronautical aluminum and plastic diffuser
Body: aeronautical aluminum T6061
Finishing: anodized, Type III
Lens: hardened glass with anti-reflective coating
Accessories: wrist strap and spare o-ring
Notes: Magnetic back - Immersible up to 2m depth, as per IPX-8 specifications

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 8x CRI diodes> 90 with warm light (4500K) with a life cycle of 50,000 hours and with a diameter of 360 °
Operating Modes: 3 white light power, 2 red light power and 2 red light signaling modes selectable with the dedicated dedicated button
Powers and Durate white light: 250 Lumens (4h.) -> 55 Lumens (9.15h.) -> 8 Lumens (56h.)
Powers and Durate red light: 40 Lumens (7.15h.) -> 5 Lumens (48h.) -> S.O.S. -> Beacon Light
Peak of power: 80 candles
Maximum illumination distance: 35m diameter.
Ignition and selection method luminsa: Power on / off and selection button
Body: ABS
Batteries: Rechargeable 1800mAh Li-Ion, integrated, equipped with a MicroUSB charging system or 2x 1.2 / 1.5V disposable / rechargeable AA batteries sold separately
Measurements: 7.52cm (Alt.) - 4.95cm (Width) - 5.38cm (Thick)
Weight: 131g. - battery included
Accessories: USB / MicroUSB charging cable
Impermeability: as per IP66 standard, it resists strong jets of water from every direction
Impact resistance: withstands falls from 1m. of height
Notes: Equipped with an integrated charging system via a MicroUSB port; when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The base of the torch has integrated a hook to hang it - The base of the torch has integrated a magnet to anchor it to the magnetic surfaces.

Il caricabatterie Q2 è universale, intelligente ed ultra rapido. Carica due batterie a 1000mAh/ora e una batteria a 2000mAh/ora.

Riesce ad identificare automaticamente che tipo di batteria avete inserito: Li-ion o IMR ed applica autonomamente la corretta tensione di carica ed il corretto voltaggio. Ognuno dei 2 slot di ricarica è gestito autonomamente da un microprocessore capace di monitorare le batterie indipendentemente. Il LED colorato di carica aiuta a tenere tutto sotto controllo indicando la carica in corso (luce rossa) e la carica terminata (luce verde).

Semplicissimo da usare: basta inserire la batteria ed al resto pensa a tutto lui.

Caratteristiche:
* Carica 1 o 2 batterie simultaneamente, anche di tipi differenti tra loro
* Ogni slot di ricarica è indipendente
* Identificazione automatica del tipo di batteria inserita
* Identificazione automatica del voltaggio
* Identificazione automatica del tipo di carica (CC, CV e TC)
* LED rosso/verde per monitorare il progresso di carica
* Spegnimento automatico della carica al completamento
* Protezione contro l'inversione di polarità
* Dissipazione del calore ottimale
* Utilizzabile su rete fissa e compatibile con accendisigari da auto (cavo non fornito)
* Certificazioni CE e RoHS

Specifiche Tecniche:
* Voltaggio Input: DC 12V / 12W
* Potenza Input: 1A (max)
* Output Voltaggio: 4.2V
* Output Corrente:2A x1 / 1A x2
* Dimensioni: 125.4x59.6x36.2mm.
* Peso senza batterie: 92g.
* Compatibile con batterie IMR e Li-Ion: 18650, 18350, RCR123, 26650, 14500, 10340, 10350, 10440, 10500, 12340, 12500, 12650, 13450, 13500, 13650, 14350, 14430, 14650, 16500, 16340, 16650, 17350, 17500, 17650, 17670, 17700, 18490, 18500, 18700, 22500, 22650, 25500, 26500, 26700, 20700, 21700, 22700

Precauzioni:
* Non ricaricare tipi differenti di batterie oltre a quelli indicati
* Non lasciare incustodite le batterie durante le operazioni di ricarica
* A batterie cariche, togliere le batterie dal caricabatterie prima di estrarre la presa elettrica per prevenire lo scaricamento delle batterie stesse

ATTENZIONE: le batterie visualizzate in foto non sono comprese.

Led: 1x Cree XM-L2 T6 - with a life cycle of 50,000 hours

Operating Modes: continuous brightness change plus strobe mode
Powers and Durations: from 0,5 (500 h) to 1000 lumens (1 h)
Peak of power: 24000 candles
Maximum illumination distance: 310m.
Ignition method: rear switch for tactical uses
Light variation method: when the torch is on, moving the rotary control counter-clockwise, the P26 will switch from Ultralow to Turbo to Strobe.
Head: aeronautical aluminum
Body: aeronautical aluminum
Finishing: anodized, Type III
Lens: ultra-clear hardened glass with anti-reflective coating
Batteries: works with a 3.7V 18650 rechargeable battery or 2x 3.0 / 3.7V disposable / rechargeable CR123A batteries (sold separately)
Measurements: 14.9cm (L) - 2.54cm (D stem) - 3.18cm (D head)
Weight: 128g. batteries excluded
Accessories: wrist strap, cordura belt sheath, spare o-rings, clip, rear rubber button, CR123A battery box
Waterproofing: as per standard IPX-8, submersible up to 2m. of depth for 30min.
Impact resistance: withstands drops from 1.5m in height

Led: Cree XP-L HI V3 with a life cycle of 50,000 hours
Operating Modes: 5 light powers, 1 strobe and 1 SOS, electronically regulated
Powers and Durations: 1800 Lumens (0.30h.) -> 850 Lumens (1.45h.) -> 300 Lumens (4.45h.) -> 55 Lumens (20h.) -> 1 Lumens (280h.) -> Strobo - > SOS -> Beacon
Peak of power: 31200 candles
Maximum illumination distance: 353m.
Ignition method: Front power button
Light selection method: Front light adjustment button
Head: aeronautical aluminum
Body: polycarbonate
Finishing: anodized, Type III
Lens: ultra-clear hardened glass with anti-reflective coating
Batteries: uses 4x 1.2 / 1.5V disposable / rechargeable AA Styles
Measurements: 16.8cm (L) - 40cm (D head)
Weight: 127.5g. - batteries not included
Accessories: wrist strap, nylon sheath, o-ring
Waterproofing: as per standard IPX-8, submersible up to 2m. of depth for 30min.
Impact resistance: withstands drops from 1m in height
Remarks: -

BATTERIES NOT INCLUDED - SOLD SEPARATELY

4-seater 18650 battery holder made of extremely resistant rubber with optional safety velcro strap.

Allows you to store and keep ordered up to 4 18650 or equivalent cylindrical batteries with a diameter not exceeding 23mm. Thanks to the convenient Velcro strap you can store batteries safely in your pocket, inserting them in a backpack or travel bag or even hanging them on your belt, if necessary.

Dimensions: 4.16x4.29x8.78cm
Weight: 44.5g.

4-seater 18650 battery holder made of extremely resistant rubber with optional safety velcro strap.

Allows you to store and keep ordered up to 4 18650 or equivalent cylindrical batteries with a diameter not exceeding 23mm. Thanks to the convenient Velcro strap you can store batteries safely in your pocket, inserting them in a backpack or travel bag or even hanging them on your belt, if necessary.

Dimensions: 4.16x4.29x8.78cm
Weight: 44.5g.

The NITECORE NL1665R is a 650mAh 16340 micro-USB rechargeable battery that's compatible with multiple 16340 flashlights, headlamps and other electronic powered devices. No charger is needed to recharge this battery, it's equipped with a built-in micro-USB port that allows users to charge the battery directly using any compatible USB power source. Yet, the battery does have the ability to recharge using a traditional charger providing multiple recharge options for users. The NL1665R is equivalent to 500 pairs of CR123 batteries and has a life span of over 500 recharge cycles, helping to reduce the cost of energy to users over time.

The battery boasts multiple external safety mechanisms like a microporous barrier to defend internal components and a pressure relief valve to protect against rapid temperature increases and explosions. A built-in high-performance protection circuit protects the battery from overcharging, over discharging and short-circuiting to prevent damage and prolong battery life.
NITECORE NL1665R Specifications
Battery Type: 16340
Capacity: 650mAh
Output: 2A
Voltage: 3.6V
Length: 1.38" (35mm)
Diameter: 0.65" (16.6mm)
Weight: 0.67oz
NITECORE NL1665R Features
Integrated micro-USB charging port
Compatible with traditional battery chargers
Pressure relief valve protection for rapid temperature increases
Microporous barrier to protect internal components
High performance protected circuit automatically protects against overcharge, over discharge and short-circuiting
Nickel-plated stainless steel protectors
Certified by International Standards
Package Contents: NITECORE NL1665R 650mAh 16340 Micro-USB Rechargeable Battery

The NITECORE NL1475R is a 750mAh 14500 micro-USB rechargeable battery that's compatible with multiple 14500 flashlights, headlamps and other electronic powered devices. No charger is needed to recharge this battery, it's equipped with a built-in micro-USB port that allows users to charge the battery directly using any compatible USB power source. Yet, the battery does have the ability to recharge using a traditional charger providing multiple recharge options for users. The NL1475R is equivalent to 500 pairs of non-rechargeable batteries and has a life span of over 500 recharge cycles, helping to reduce the cost of energy to users over time. 

The battery boasts multiple external safety mechanisms like a microporous barrier to defend internal components and a pressure relief valve to protect against rapid temperature increases and explosions. A built-in high-performance protection circuit protects the battery from overcharging, over discharging and short-circuiting to prevent damage and prolong battery life.

NITECORE NL1475R Specifications

• Battery Type: 14500
• Capacity: 750mAh
• Output: 2A
• Voltage: 3.6V
• Length: 1.95" (49.5mm)
• Diameter: 0.56" (14.2mm)
• Weight: 0.66oz (18.6g)

NITECORE NL1475R Features

• Integrated micro-USB charging port
• Compatible with traditional battery chargers
• Pressure relief valve protection for rapid temperature increases
• Microporous barrier to protect internal components
• High performance protected circuit automatically protects against overcharge, over discharge and short-circuiting
• Nickel-plated stainless steel protectors
• Certified by International Standards

Package Contents: NITECORE NL1475R 750mAh 14500 Micro-USB Rechargeable Battery

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 1x Cree XP-G2 S3 + 1x LED auxiliary white color CRI> 90 + 1 LED auxiliary red color. All with a life cycle of 50,000 hours
Operating Modes: 4 light powers, selectable with the dedicated dedicated button and 2 signaling modes. 1 Auxiliary white light, 2 red light power and intermittent signaling
Powers and Durate primary white light: 360 Lumens (0.5h.) -> 190 Lumens (5h.) -> 38 Lumens (8h.) -> 1 Lumen (160h.) -> S.O.S. -> Beacon Light
Powers and Durations auxiliary white light: 20 Lumens (6.15h.) - with maximum capacity of 5.5m
Powers and Durations auxiliary red light: 13 Lumens (7.45h.) - with maximum range of 4m -> 0.9 Lumens (68h.) -> Caution (13h.)
Peak of power: 1600 candles
Maximum illumination distance: 81m.
Ignition and selection method luminsa: Power on / off and white lights button + Power on / off button and red light selection
Body: ABS
Batteries: 610mAh Li-Ion, integrated, not removable, equipped with integrated MicroUSB charging system
Measurements: 5.55cm (Lenght) - 3.46cm (Width,) - 2.32cm (Thick)
Weight: 28g. - battery included
Accessories: front elastic band
Waterproof: IP66 standard: resistant to strong splashes of water
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with integrated charging system via MicroUSB port (cable included in the package); when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The auxiliary white light allows to illuminate at 100 ° amplitude. The inclination adjustment system allows to lower the torch up to 60 °

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 1x Cree XP-G2 S3 + 1x LED auxiliary white color CRI> 90 + 1 LED auxiliary red color. All with a life cycle of 50,000 hours
Operating Modes: 4 light powers, selectable with the dedicated dedicated button and 2 signaling modes. 1 Auxiliary white light, 2 red light power and intermittent signaling
Powers and Durate primary white light: 360 Lumens (0.5h.) -> 190 Lumens (5h.) -> 38 Lumens (8h.) -> 1 Lumen (160h.) -> S.O.S. -> Beacon Light
Powers and Durations auxiliary white light: 20 Lumens (6.15h.) - with maximum capacity of 5.5m
Powers and Durations auxiliary red light: 13 Lumens (7.45h.) - with maximum range of 4m -> 0.9 Lumens (68h.) -> Caution (13h.)
Peak of power: 1600 candles
Maximum illumination distance: 81m.
Ignition and selection method luminsa: Power on / off and white lights button + Power on / off button and red light selection
Body: ABS
Batteries: 610mAh Li-Ion, integrated, not removable, equipped with integrated MicroUSB charging system
Measurements: 5.55cm (Lenght) - 3.46cm (Width,) - 2.32cm (Thick)
Weight: 28g. - battery included
Accessories: front elastic band
Waterproof: IP66 standard: resistant to strong splashes of water
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with integrated charging system via MicroUSB port (cable included in the package); when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The auxiliary white light allows to illuminate at 100 ° amplitude. The inclination adjustment system allows to lower the torch up to 60 °

3.7V rechargeable IMR battery currently only compatible with Nitecore EC11 and MT10C torches

Rechargeable with Nitecore - Intellicharger i2 EU and Nitecore - Intellicharger i4 EU

Equipped with nickel-plated stainless steel front and rear plates to ensure the best impact resistance, abrasion and corrosion resistance, ensuring maximum electrical conductivity. Suitable for highly energy-consuming electronic devices.

* Rechargeable Battery IMR18350A 3.7V - 700mAh - 7A
* Life cycle: over 500 refills
* Capacity: 700mAh
* Battery size: 18mm in diameter x 34.8mm in length (have a diameter larger than common CR123A / 16340)
* Weight: 20g

WARNING: Positive Flat Plate Battery - This battery has a different diameter than the 16340 / CR123A batteries - Use only in IMR-compatible batteries - Observe the polarity of the batteries when charging and in use - Before to buy and use rechargeable batteries, make sure your device supports them by consulting the manufacturer's manuals.

Questa torcia è dotata di un pratico sistema di ricarica integrato tramite plug MicroUSB che permette di ricaricare batterie di tipo 18650 (1x 18650 da 3400mAh inclusa nella confezione)

Potenze e durate certificate da standard ANSI/NEMA FL1 testate con 1x 18650 3.6V da 3400mAh

LED: 1x Cree XM-L2 U2 con ciclo vitale di 50,000 ore
Luce bianca principale: 5 output luminosi costanti, regolati digitalmente e selezionabili premendo l'apposito pulsante switch mode e 3 segnalazioni (police warning, S.O.S., location beacon)
Potenze e durate: 1 lumen (680 h.)  -> 38 lumens (25 h.) -> 210 lumens (7.15 h.) -> 420 lumens (2.30 h.) -> 1000 (1h.)
Luce bianca ausiliaria: 26 lumens (25h.)
Luce rossa ausiliaria: 11 Lumens (20h) -> Caution 11 Lumens (32h)
Portata: fino a 110mt.
Picco di potenza: 3000 candele
Batterie utilizzabili: 1x 18650 3400mAh da 3.7V (inclusa nella confezione) o 2x CR123A da 3.0/3.7V usa e getta o ricaricabili
Dimensioni torcia: 82.7x33.3 mm. 
Peso: 62.7g (senza batteria)
Lente: in vetro indurito con trattamento anti riflesso
Corpo: in alluminio aeronautico
Finitura: anodizzata, Type III
Cinghia: elastica, regolabile in diametro ed in altezza
Note: resistente all'acqua come da standard IP68, immergibile a 2mt. di profondità per 30min. 
Accessori: 1x Batteria 18650 3.7V da 3400mAh - cavo di ricarica USB/MicroUSB - cinghia elastica frontale - o-ring di ricambio
Sistema Integrato di Ricarica: attraverso la porta MicroUSB integrata - protetta da una copertura isolata - e utilizzando il cavo Micro-USB fornito di serie è possibile provvedere alla ricarica della batteria in dotazione, l'operazione è monitorabile grazie ad un apposito led luminoso posto accanto sotto i pulsanti di selezione luminosa. Il cavo di ricarica può essere attaccato a qualsiasi PC dotato di porta USB o a qualsiasi alimentatore da parete o da accendisigari dotato di porta USB.

Clicca il link per visionare una recensione approfondita del modello Nitecore HC65

The new Nitecore NL1826R 18650 battery is a revolutionary battery designed with a built-in micro-USB charging port making charging easier than ever! No more need for an extra charger as this battery can be charged directly using a standard micro-USB charging cable (sold separately). Simply plug the battery into an available power source and a red indicator light under the + pole will turn green upon completion. Alternatively, these batteries can still be charged on an external charger if desired. The NL1826R batteries are designed for powering high drain devices such as high-output flashlights, lanterns, headlamps, and bike lights, as well as a variety of other appliances and devices. With built in smart charging circuitry built and other integrated safety features through-out, this battery will safely work in the majority of button-top compatible devices.

Features & Specifications:
Type: Nitecore NL1826R 18650 3.6V Protected Li-ion rechargeable battery
Capacity: 2600mAh
Voltage: 3.6V
Output: 12.24Wh
USB Charging Voltage: 5V
USB Charging Current: 800mA (Maximum)
Chemistry: Lithium-ion
Weight: 1.52oz (47.3g)
Length: 2.68in (68mm)
Diameter: 0.72in (18.3mm)
Protected: Internal PCB protection prevents under-voltage at 2.5V and over-voltage at 4.25V
Recharge: up to 500+ cycles
Red & Green charging indicator LED's
Microporous barrier and pressure release valves help protect the battery and prevent damage caused by rapid expansion & combustion
12 Month Warranty Period

Tactical Backpack Cordura, lightweight and durable, designed for hiking, tactical and urban use.

Features and Materials:

- Cordura Nylon 1000 denars water resistant and abrasion with synthetic velvet parts
- External fabric treatment that ensures dirt resistance and facilitates maintenance
- Designed for intense use and excursion
- Compartment pockets to accommodate different utensils
- Padded and ventilated back and shoulder straps
- Reinforced handle
- Anchor Points for LED Signaling Lights (eg Nitecore NU05)
- Stretched and long size Zip, comfortable to use with gloves
- Large Velcro area for anchoring patches and various objects
- Compression center belt for anchoring objects and compacting the load
- MOLLE Compatible Front to Expand and Modify the Backpack
- Side nylon bandlets for hooking up items and additional buffets
- Large internal pocket, can accommodate a laptop of 13 "
- Integrated clip to hold water bags, bottles and hydratation packs
- Integrated rain cover in the back of the backpack
- Dimensions: 45x28x12 cm.
- Volume: 20 l.
- Weight: 1.5 kg.

Powers and durations certified in the laboratory by ANSI / NEMA FL1 standards

Led: 9x CRI diodes> 90 with warm light (4500K) with a life cycle of 50,000 hours and with a diameter of 360 °
Operating Modes: 3 light powers, selectable with the appropriate dedicated button and 3 signaling modes
Powers and Durations: 250 Lumens (1h.) -> 65 Lumens (5.15h.) -> 8 Lumens (38h.) -> Caution Light -> S.O.S. -> Beacon Light
Power peak: 38 candles
Maximum illumination distance: 24m diameter.
Ignition and selection method luminsa: Power on / off and selection button
Body: ABS
Batteries: Rechargeable Li-Ion from 4.44Wh, integrated, equipped with a MicroUSB charging system
Measurements: 6.55cm (Alt.) - 5cm (Width) - 2.48cm (Thick)
Weight: 49g. - battery included
Accessories: front elastic band
Impermeability: as per IP66 standard, it resists strong jets of water from every direction
Impact resistance: withstands drops from 1.5m in height
Notes: Equipped with an integrated charging system via a MicroUSB port; when charging, an integrated LED will show the status and it will switch off automatically when the charging is complete. The recharging system automatically prevents undervoltage, overvoltage and has integrated protection against short circuits. - The base of the torch has integrated a hook to hang it - The base of the torch has integrated a magnet to anchor it to the magnetic surfaces.

Destination of use: Sports

Type of production: Industrial
Country of production: USA
Blade: 420HC stainless steel
Blade treatment: Satind
Handle: Nylon
Blade length: 65mm.
Blade thickness: 2mm.
Length closed: 100mm.
Total length: 1654mm.
Thick when closed: 14mm.
Balancing: -
Weight: 72g.
Opening: Opening pin on the back of the blade
Washers: in brass
Closure: Liner Lock
Clip: stainless steel, removable
Sheath: -
Packaging: Cardboard box with Leatherman logos
Notes: Carabiner / retractable bottle opener

Emergency double chamber whistle made entirely of one piece of titanium. Lightweight and biocompatible, it produces 120 whistle decibel with the slightest breath effort.

Ideal both in hiking environment as an emergency whistle, as well as in the urban environment as a deterrent against aggression or even in a sports environment.

* Weight: 12.6g
* Total Length: 52mm.
* Material: titanium, with internal teflon resonator
* Width and Height: 14x7mm

power and durability certified by ANSI / NEMA FL1 standard using 2x AA 1.2V 2500mAh - under different conditions of use or using different batteries, data may vary

Led: Cree XP-G2 S3 with a lifetime of 50,000 hours
Operating Modes: 3 light powers, electronically controlled
Powers and Duration: 260 Lumens (2.15h.) -> 45 Lumens (18h.) -> 1 Lumens (180h.)
Power peak: 2400 candles
Maximum illumination distance: 98m.
Power Button Rear Button Button:
Light Selection Method By slightly pressing the rubber back button
Head: Aeronautical aluminum
Body: ABS
Finish: anodized, Type III
Lens: Ultra-hardened hardened glass with anti-reflection treatment
Batteries: (sold separately) uses 2x AA disposable / rechargeable 1.2 / 1.5V
Measurements: 80.9cm (Length) - 40.7cm (Width) - 2.1cm (Thickness)
Weight: 49g. - Batteries not included
Accessories: clip - wrist strap - spare o-ring
Waterproof: as standard IPX-8, immersible up to 2mt. of depth for 30min.
Impact Resistance: Resists to 1.5m high falls

A discreet, indestructible pen that doubles as a glass breaker and self defense tool.


Hollowed out from a solid block of titanium, this pen is unbreakable, will not stain, will not rust, does not peel, doubles as a glass breaker and self defense tool, looks insanely cool and comes in a swanky aluminium case. I don’t know a better writing instrument then this. Did we mention it can write on any surface, is waterproof and works even in space?

The tungsten steel tip makes it an effective window breaker. A deep carry pocket clip makes sure it remains discreet in your pocket.

It also comes with a Fisher pressurised cartridge that's waterproof, temperature proof and can be used to write upside down and of course if you ever need to write something in space, you can.A superb companion for business wear and an exquisite gift for anyone.

* Weight: 18g
* Total Length: 107mm.
* Material: titanium
* Diameter: 9 mm.
* Glass breaking tip: tungsten steel
* Ink: black with Fisher PR4 refill. It writes at temperatures from -35 ° to over 120 °, underwater, on dirty and oily surfaces, lasts 15 times more than a normal, non-pressurized refill, can trace a 14km continuous line thanks to the particular thixotropic ink, semi-solid consistency, which is rendered fluid by the special tungsten ball.

Potenze e durate certificate in laboratorio da standard ANSI/NEMA FL1

Led: 1x Cree XP-G2 con un ciclo vitale di 50.000 ore e con diametro di illuminazione di 100°
Modi Operativi: 4 potenze luminose, selezionabili con l'apposito pulsante dedicato
Potenze e Durate: 360 Lumens (0.5h. ) -> 150 Lumens (1.5h.) -> 35 Lumens (6.30h.) -> 1 Lumen (46h.)
Picco di potenza: 1400 candele
Distanza di illuminazione massima: 74m.
Metodo di accensione: Pulsante anteriore di accensione e spegnimento
Metodo di selezione luminosa: Pulsante anteriore di selezione luminosa
Corpo: acciaio inox con anodizzazione PVD 
Batterie: Li-Ion, inclusa, non rimovibile, dotata di sistema di ricarica integrato di tipo MicroUSB
Misure: 6.1cm (Lungh.) - 2.4cm (Largh,) - 1.35cm (Spess.)
Peso: 32g. - batteria inclusa
Accessori: doppio anello in acciaio per aggancio
Impermeabilità: come da standard IP54, resiste a polvere e a leggeri spruzzi d'acqua
Resistenza agli impatti: resiste a cadute da 1.5m di altezza
Note: Dotata di sistema di ricarica integrato tramite porta MicroUSB (cavo non compreso nella confezione); in fase di ricarica, un LED integrato mostrerà lo status e si spegnerà automaticamente a ricarica completata. Il sistema di ricarica previene automaticamente il sottovoltaggio, il sovravvoltaggio ed ha una protezione integrata contro le cortocircuitazioni. - Il gancio posteriore della torcia, pensato per ancorarla ad un portachiavi o ad ulteriori attrezzature, resiste ad una trazione di massimo 30kg.

power and durability certified by ANSI / NEMA FL1 standard using 1x 18650 Li-Ion 3.7V 3400mAh - under different conditions of use or using different batteries, data may vary

Led: 1x CREE XP-L HI V3 LED with a life cycle of 50,000 hours
Operating Modes: 2 white light power, 2 red light power and 1 strobe all electronically controlled
Power and Duration: White Light: 1000 Lumens (1.15h.) -> 385 Lumens (4h.) -> Strobe - Red Light: 115 Lumens (4.15h.) -> 55 Lumens (9h.)
Power peak: 12400 candles
Maximum illumination distance: 223m.
Power method: Multifunctional front button
Light Selection Method: Multifunctional front button
Head: Aeronautical aluminum
Body: Aeronautical aluminum
Finish: anodized, Type III, with anticorrosion treatment to withstand brackish water
Lens: Ultra-hardened hardened glass with anti-reflection treatment
Battery: (sold separately) 1x Li-Ion / IMR 18650 rechargeable 3.6 / 3.7V or 2x CR123 3.0V
Measurements: 13.3cm (L) - cm (D stem) - cm (head D)
Weight: 143g. - Batteries not included
Impact Resistance: Resists to 1.5m high falls
Waterproof: as standard IPX-8, immersible up to 30m. of depth
Notes: Torch conceived for underwater use up to depth of 30m. - Includes a front pocket diving pointer in the flashlight, a wrist strap and two spare o-rings.

Useful, compact, lightweight and powerful, this new Nitecore product comes with 2 red led and 2 two white led. Thanks to the small size it is perfect for cycling, walking, applying to pets, to run.

Through a single central button, the user can choose four different bright outputs:

Fixed white (35 lumens) - Ideal as motion light
Red - slow flashing (4 lumens) - Ideal for hiking
Red - fast flashing (4 lumens) - Ideal for position reporting
White - slow flashing (35 lumens) - Ideal for position reporting

Powers and durables certified by ANSI / NEMA FL1 standard

Light color: white and red
Materials: plastic
Mode: Red light (slow flashing), red light (flashing fast), white light (slow flashing), fixed white light
Lumens: 4LM, 4LM, 35LM, 35LM
Duration: 9h, 9h, 2h15min, 2h15min
Battery: Built-in 3.7V - 120mAh Li-ion Battery
Switch Type: Pressure
Impact resistance: 1.5 meters
Max Output: 35 lumens
Waterproof: IP66 (dustproof and waterproof)
Weight: 10.4g
Measurements: 29.5mm x 30.3mm x 16.3mm

USB Rechargeable

Reload as a smartphone!
This torch is home to a rechargeable 18650 battery and is equipped with an innovative charging system with built-in USB / Micro USB plug.

Laboratory Potentials and Durability Standards from ANSI / NEMA FL1 Standard using 1x 18650 3.7V 3400mAh - under different conditions of use or using different batteries, the data may vary

Led: 1x Cree XP-L HI V3 - with a lifetime of 50,000 hours
Operating Modes: 7, electronically adjusted
Power and Duration: 1000 Lumens (1h and 15min.) -> 280 Lumens (6h) -> 55 Lumens (28h) -> 1 Lumens (520h.) -> Strobo -> SOS -> Location Beacon
Power peak: 25700 candles
Maximum illumination distance: 320m.
Power method: Rear button with "Momentary On" system for light signals
Light selection method: Front button under the head
Head: Aeronautical aluminum
Body: aeronautical aluminum
Finish: anodised, Type III
Lens: ultra-hardened hardened glass with anti-reflection treatment
Batteries: works with a 3400mAh rechargeable 18650 3.7V battery already included in the box
Measurements: 13.9cm (L) - 2.54cm (D stem) - 2.54cm (D head)
Weight: 88g. Batteries excluded
Accessories: wrist strap, cordura belt buckle, spare o-ring, clip, spare rubber for the micro-usb plug, spare rubber button
Waterproof: as standard IPX-8, immersible up to 2mt. Of depth for 30min.
Impact Resistance: Resists to 1.5m high falls

1800 Power Lumens with One Battery IMR18650 - Highest Pocket Size, Only 11cm Long. And with magnetic back cap.

Laboratory Potentials and Durability Standards from ANSI / NEMA FL1 Standard using 1x 18650 IMR 3.6V 3100mAh - under different conditions of use or using different batteries, the data may vary

Led: 1x CREE XP35 HD E2 LED with a life cycle of 50,000 hours
Operating Modes: 5 electrically regulated light powers
Powers and Dates: 1800 Lumens (30min.) -> 810 Lumens (1.30h.) -> 300 Lumens (4h.) -> 80 Lumens (15h.) -> 1 Lumen (300h.) -> Strobo -> Location Beacon
Power peak: 12100 candles
Maximum illumination distance: 220m.
Power method: Multifunctional front button
Light Selection Method: Multifunctional front button
Head: Aeronautical aluminum
Body: Aeronautical aluminum
Finish: anodised, Type III
Lens: ultra-hardened hardened glass with anti-reflection treatment
Battery pack (included in the package): 1x 3.6V and 3100mAh rechargeable IMR 18650 - It can also work with 1x 18650 Li-Ion 3.7V or 2x CR123 3.0V without ever achieving 1800 lumens of power
Measurements: 11.1cm (L) - 2.38cm (D stem) - 2.45cm (D head)
Weight: 62g. - Batteries not included
Impact Resistance: Resists to 1.5m high falls
Waterproof: as standard IPX-8, immersible up to 2mt. Of depth for 30min.
Notes: Magnetic back cap can be hooked to any metal surface - to produce 1800 lumens of power, it is mandatory to have a 3.6 / 3.7V IMR18650 battery with a current output greater than 8A, such as that already supplied with the torch.